企業品牌形象設計對于標牌制作的一些規定

    在企業品牌標識制作時需要注意那些功能與材料呢，我們立足于這些事業中，需要針對那些功能呢。先把蝕刻好的不銹鋼板放入清水中，用干凈的布將三氯化鐵溶液洗去。然后放入另一個盛有清水的容器中，擺動幾下，將表面洗干凈,再把不銹鋼板反面貼的防腐保護膜撕掉，將這二塊不銹鋼板，放在盛有固體氫氧化鈉的容器里，按1：10左右的比例加入七、八十度的熱水，擺動容器，使氫氧化鈉充分的溶解。我們可以看到，兩塊不銹鋼板上殘留的膜都會慢慢地全部退去。擺動到水溫為二、三十度了，才可以拿干凈的布將它們擦洗干凈。再把不銹鋼板放入盛有清水的桶中進行漂洗。

    我們的創意就是需要這樣的品牌來實現目票，蝕刻好的酒店標牌半成品就是這個樣子。企業品牌形象設計讓它自然晾干就行了。三、后期處理要把酒店標牌半成品加工到成品，后期處理也是必不可少的。

    標牌的制作一些規定就是從這里開始的了。這個環節主要是電鍍。電鍍是指借助直流電的作用，讓金屬的半成品在溶液中進行電解反應，從而在它的表面，均勻地附上一層薄薄的別的金屬或合金。現在各地政府都規定，電鍍只能由專業的電鍍公司來進行。因此對于電鍍，我們只是單的介紹它的工藝流程。(一)電鍍電鍍前，先在酒店標牌半成品預留的地方，用臺鉆鉆個小孔，把能導電的銅絲從小孔中穿過一小段綁好，另一頭留出足夠的長度。

   標牌的制作電鍍一般有多個環節組成，可根據需要進行。
   標牌的制作電鍍前4小時將電鍍槽的總電源開啟，標牌的制作進行預熱。

Corporate brand image design some of the provisions made ​​for signage

     Corporate brand identity in the production function and the need to pay attention to those materials, let the cause based on the need for those features yet. Good first etched stainless steel plate into the water, with a clean cloth to wash away the ferric chloride solution. Then put into another Shengyou Qing water container, a few swings, the surface clean, then paste the corrosion of stainless steel plate protective film negative to tear up these two stainless steel plates, placed filled with solid sodium hydroxide containers, the ratio of about 1:10 to join seven, eighty-degree water, swing container, so full of sodium hydroxide dissolved. We can see, two stainless steel plate residual film will slowly recede all. Swing to the temperature of twenty or thirty degrees, and it can take a clean cloth to scrub them clean. Then placed in Shengyou Qing stainless steel bucket for rinse water.

     Our brand of creativity is needed to achieve this target votes, semi-finished etching plate is a good hotel like this. Let it dry on the line. Third, post-processing to make the hotel sign semi-finished products processing, post-processing is also essential.

     Signs of the production is from here some of the provisions of the. This link is mainly electroplating. Plating is the use of direct current role, so that semi-finished metal electrolytic reaction in solution, resulting in its surface, evenly attached to a thin layer of another metal or alloy. Now local governments are set, electroplating plating only by a professional company to carry out. So for electroplating, we just introduced its single process. (A) electroplating plating before signs semi set aside in the hotel where, with a bench drill drill holes, the conductive wire can pass through a small hole in the tie from the other end leaving enough length.

    Sign production plating generally have multiple sessions, may be needed.
    The production of signs will be 4 hours before plating plating bath on the total power, making signs to warm up.